 |
Ampere Hour Meters pH And ORP Indicators and Controllers Humidity Indicators Conductivity Indicators Data Loggers Systems Flow Indicators and Controllers Peak Load Indicators Production Display Boards Calibrators Equipment Speed Indicators Digital Counters Digital Timers Universal Programmable Timer Sequential Timers 2 Digit Timer With Pushwheels 4 Digit Timer With Pushwheels And Battery Backup 3 Digit Timer With Pushwheels 2 Digit On/Off Repeat Cycle Timer Timers with 3 Thumb Wheel Settings (Without Display) Timers with 2 Thumb Wheel Settings (Without Display) Temperature Indicators Process Indicators and Controllers Clean Room Monitor Digital ReadOut for Encoders Temperature Logger
|
|
|
|
|
|
| | Universal Programmable Timer Model 1050We manufacture and offer digital timers that are used in diverse commercial applications. Based on our immense technical expertise, we are able to provide timers in custom-made designs and sizes to suit different needs of our clients. Our digital timers have the following features: - 4 different timing ranges of 99.99sec, 999.9sec, 99Mins59Secs, 99Hrs59Mins
- Press to start/Power On start/Cyclic modes settable
- Delayed On/Off programmable by user from front panel
- Up/Down time counting user settable
- User settable starting On/Off time for cyclic mode
- Number of cycles settable for cyclic mode
- Non-volatile memory to save configuration and timing
- Configuration lockable by rear jumper
- Front Reset/Start switch with parallel terminals at rear
- Aesthetically designed panel with membrane switches
Specification :
| Display | 4 Digit 0.56” Red 7 segment LED display 4 Red LEDs to indicate selected timing range Red LED to indicate current status of Relay On/Off | | Modes | User settable from front panel Power On start Press to start (with battery backup selection using EEPROM) Cyclic action | | Number of Cycles | 1-99 cycles settable for cyclic mode after which the timer stops Setting number of cycles to Zero disables number of cycles setting | | Reset/Start | Front Reset/Start switch with parallel terminals at rear to connect additional switch, if required. | | Relay Logic | Settable delayed On/Off, 5 Amps/220V AC Dual Relay Contact outputs | | Timing direction | Up/Down time counting user settable | | Memory | Non-volatile EEPROM to save settings | | Configuration Lock | Open terminals 1&2 to lock all configurations | | Supply | 220V AC ± 15% @ 50/60Hz | | Dimensions | Front Fascia: 96mm x 96mm x 135mm Cut Out: 91mm x 91mm |
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
| Sequential Timers Model 1010We offer Sequential Timer Model 1010 that are appreciated by the clients for international quality standards. Offered with Remote start of operation selectable via external contact, our Sequential Timer Model 1010 has a Separate LEDS to indicate current active channel. These are available with 10 output sequentially programmable timer to ensure optimum performance. Following are some of the features of our Sequential Timer Model 1010: - Each channel has on time & off time individually settable
- Separate LEDS to indicate current active channel
- Time settable from 0.01 seconds to 99.59 hours
- Individual timing range for each channel
- Single cycle or cyclic operation selectable
- Provision for skipping of undesired channels
- Cascading of more than one instrument for sequential operation of more than 10 relays possible
- Provision for intermediate freezing of operation
- Saving of time status on power failure
- On line programming for changing settings during operation
Our Sequential Timer Model 1010 has below mentioned technical specification: | Display | -
0.56” 7 Segment Red LED 4 digit display for time -
0.56” 7 Segment Red LED single digit display for active channel -
10 Red LEDs for indication of current channel relay On -
3 LEDs to indicate the resolution of the timing of the current channel -
2 LEDs to indicate On or Off cycle of a channel | | Timer Display | | | Range Selectable | | | 5 Sets Of Contacts | -
Marked “A” to “E” -
“A”: If contacts are shorted, timer recycles/re-starts at end of sequence. If contacts are open only single sequence operation present -
“B”: Cascading input -
Used for trigger start on momentary closing of contact OR To cascade 2 such timers, connect “E” contacts of first timer to “B” contacts of next timer -
“C”: If contacts are open the timer resets to channel 0 and time 0 on power on If contact are shorted, the timer resumes operation from where it left off at power failure (same channel and same time) -
“D”: Inhibit/HoldIf contacts are shorted, the timer operation freezes. If opened, it resumes. -
“E”: Cascading output Used as input from previous timer to cascade more than one instrument | | Number of Relays | channels can be skipped by setting the On and Off time of that channel to zero |
| | |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| | 2 Digit Timer With Pushwheels Model 1052 - Quartz Crystal Base for 0.01% Accuracty/Repeat Accuracy.
- Ranges Covering 0.01 sec. to 9999 min.
- Resolution for 0.01, 0.1, 1 sec. OR 0.1, 1 Min. OR 0.1 Hr.
- Delayed On/ Delayed Off Process or Cascading Operation.
- Single/ Cyclic/ Sequence/ Cyclic-cum-Sequence Operation.
- Mains/Remote/Push Button Initiation.
- Blind/Digital Timers.
- Din Standard 96 x 48, 96 x 96 & 96 x 192 mm Panel/Wall Mounting Case.
- 110 V AC, 230 V AC, 12 V DC or 24 V DC Operation.
- Potential Free Ouptut in the form of 2 Change Over Relay Contact @5A/230V AC or Solid State Relay with AC Output.
- 'Instant On' Relay also available as option.
- Setting by Thumbwheel Switches.
- Independent of Mains Frequency/Voltage Variations
Specification
Display: 2 Digit(0.5 inch Red 7 Seg) Range : Internally Adjustable with Jumbers for 9.9sec, 99 sec, 9.9min OR 99min Mode: Delay On/Delay Off Internally Adjustable Supply: 220V AC +/- 15% 50HzSize: 96mm x 96 mm or 72mm x 72mmMounting: Panel Type
|
| |
|
|
|
|
|
|
|
|
|
