We are engaged in manufacturing and supplying Ampere Hour Meters and Ampere Minute meters for a wide range of applications for precision electroplating and battery testing applications.

Electroplating: Plating thickness is directly proportional to the integration of current over a period of time. The preset Amp-Hr or Amp-Min limit ensures precision repeatability and uniformity of the plating thickness guaranteeing quality and avoiding wastage of material. Time controlled dosage pumps allow automation. Hence where there is a criticality of thickness of plating and uniformity is required, Ampere Hour/Minute Meter is the solution. For example, gold plating, rhodium plating, platinum plating etc.

Battery Testing: The instrument integrates the current while allowing the charged battery to discharge through a load until the battery voltage falls below the specified limit (10.5V for a 12V battery), to give a measure of the AH rating of the battery.

Programmable Amp-Hour Meter

Model-800AH

We offer model 800AH programmable amp-hour meter, that is used for electroplating thickness control and testing battery Amp-Hr. These meters are available with 6 RED 7 Segment LEDs of 0.56” character height. However, the current display is fixed at Max 9999 Amps using a shunt of current & 75mV for user programmed. Following are some of the features of our model 800AH programmable amp-hour meter:

Shunt calibration programmable
Stores cumulative Amp-Hour
Instantaneous current display
Settable Limit for Amp-Hr/Min
Front membrane switches for easy operation
Non-volatile memory for storing settings, hence no battery required

Further, our Model 800AH Programmable Amp-Hour Meter has below mentioned technical specifications:

Amp-Hour: Max 9999 A-H for each preset cycle. (Amp-Hour range is selected by shorting Pin 17-18 at the rear)
Amp-Minute: Max 9999 A-Min for each preset cycle. (Amp-Minute is selected, opening the link between Pin 17 & 18).
Max shunt: Max value of 9999 Amp corresponding to 75mV
Totalize: 6 Digits for Amp-Hour or Amp-Min. i.e. 99, 99, 99. (readable for 10 sec by going into ‘total’ mode)
Limit: Up to 9999 AH or Amin. Setting (In limit mode using incr. & decr. switches).
Relay Contact: One NO-P-NC of 5 Amp rating.
Trigger start: By pressing front panel switch or closing a rear external contact.
Battery Back-Up: Not required. Programmed values & readings, including A-H stored in EEPROM.
Lock: Electronic lock for calibration (open link between Pin 1 & 2 to lock CAL) Low Volt.
Trigger: Set at 10.5V internally, for testing 12V Battery AH. (With Pin 3 & 4 shorted)
Increased Res.: 0.1AH or 0.1AMin facility by shifting internal jumper
Supply: 220V AC 10%
Size: Front Fascia 96 mm x 96 mm, Depth 135 mm, Cut Out: 91 mm x 91 mm.
Weight: 800 grams

Send Enquiry

Ampere-Hour/Minute Meter With Dual Time Relays

Ampere-Hour/Minute Meter With Dual Time Relays

Model-804AH

We are engaged in manufacturing Ampere-Hour & Minute Meters Model 804AH, that are designed and developed aesthetically with membrane switches for the front panel. These are offered with shunt calibration programmable of up to 9999 for 75 mV. We also offer separate displays for current and ampere-hours per min. Following are some of the features and specifications of our Ampere-Hour & Minute Meter Model 804AH:

Ampere-Hour/Minute selectable
Cumulative Ampere-Hour stored on power failure
Settable limit for Ampere-Hours
Dual time relays with on time settable
Rear calibration lock to prevent tampering with settings

Specifications:

Display	4 Digit 7 Segment Red LED display for Current 6 Digit 7 Segment Red LED display for Ampere-Hours/Mins 2 Red LEDs to indicate status of the 2 Relay contacts
Shunt Calibration	Maximum 9999 Amps corresponding to 75mV settable from front panel
Set Point	Settable from 0-999999
Resolution	1AH/0.1AH/1AM/0.1AM
Totaliser	6 Digits for Ampere-Hour or Ampere-Minutes
Time Relays	2 relay contacts with individual time settings in Min.:Sec.
Contact Rating	NO-P-NC @ 5Amps/220V AC
Memory	Settings and Ampere-Hours saved in solid state EEPROM
Lock	By rear jumper to prevent accidental tampering with settings
Supply	220V AC ??? 10% @ 50/60Hz
Size	Front Fascia 96 mm x 99 mm Depth 135mm. Cut Out: 91 mm x 91 mm.
Weight	800 grams

Send Enquiry

Programmable Amp-HR Meter

Model-803AH

Programmable Amp-Hr Meter With Separate Voltage And Current Displays

Ideal for ensuring electroplating thickness by presetting AMP-HOUR
Useful for checking Amp-Hour of rechargeable batteries using voltage limit
Separate displays for Voltage, Current and Amp-Hour
Programmable for AH/0.1AH/Amin/0.1AMin
Usable with any shunt by setting ‘Calibration’ for Amp-75mV
Calibration factor lockable from rear
4 Digit Amp-Hour and 6 Digit cumulative Amp-Hour display
Attractive front panel membrane switches in rugged Aluminum cabinet
In case of power failure, the current status of selected parameters, the current Amp-Hour and Cumulative Amp-Hour is saved

Specification

Display	:All of 0.56in character height Red 7 Segment displays a.3 Digits to display voltage 0 – 99.9V b.4 Digits to display current 0 – 999.9Amps c.6 Digits to display Amp-Hour (4 Digit) and cumulative Amp-Hour (6 Digit)
Max. Shunt	: Max. value of 999.9 Amps corresponding to 75mV. User programmable from front in ‘CAL’ mode. (Max. value of 9999Amps also available on request)
Selection of Amp Hour/Min	: Short Pin 17-18 for Amp-Hour Open link of Pin 17-18 for Amp-Minute
0.1AH/Amin	: Higher 0.1 resolution by shifting internal jumper by opening cover
Totaliser	: 6 Digit readable in ‘Total’ Mode
Limit	Up to 9999 Ahr/Amin settable in limit mode using increment/decrement switches
Relay	: NO-P-NC of 5 Amp at 220V AC contact rating
Start	: Pressing front panel switch or momentarily shorting rear Pins 5 & 6 by wiring an external switch
Memory	:Non-volatile EEPROM solid state memory Stores programmed value of shunt, preset value, current Amp-Hr and the current Cumulative Amp-Hr to preserve current status on power failure
Lock	: Open Link between Pin 1 & 2 to Lock ‘Cal’ i.e. shunt value
Low Voltage Stop	Internally set at 10.5V for testing 12V battery. Short Pins 3 & 4 for this function
Supply	: 220V AC ± 10% at 50/60Hz
Size	: Vertical type with front panel 96 x 192 mm
Terminals	: At rear with marking for wiring
Mounting	: Panel Mounted
Fuse	: At rear of 0.2Amps

Send Enquiry

Programmable Ampere Hour Meter

Model-805AH

Shunt calibration programmable up to 9999 for 75mV
Ampere-Hour/Minute selectable
Ampere-Hour stored on power failure
Settable limit for Ampere-Hours
Time relay with on time settable in Mins:Secs
Rear calibration lock to prevent tampering with shunt settings
Aesthetically designed front panel with membrane switches

Specification:-

Display	4 Digit 7 Segment Red LED display for Ampere
Shunt Calibration	Maximum 9999 Amps corresponding to 75mV
Set Limit	Settable from 0-9999
Resolution	1AH/1AM
Time Relay	Relay contact with time settings in Mins:Secs
Contact Rating	NO-P-NC @ 5Amps/220V AC
Memory EEPROM	Settings and Ampere-Hours saved in solid state
Lock with shunt settings	By rear jumper to prevent accidental tampering
Supply	220V AC ± 10% @ 50/60Hz
Size	Front Fascia 96mm x 99mm Depth 135mm. Cut Out : 91mm x 91mm.
Weight	800 grams